Products – Page 17

DISPERSION CHARACTERIZATION RIG (DCR) INTERFACE SYSTEM

CANTY’s DCR is a system designed to track and monitor the interface between two fluids as separation occurs, at temperature. This allows a user to measure the amount of time it takes for interfaces to form, amounts of fluid in the different phases, and to measure any rag layers.

MORE INFO

FREE WATER & TSS IN LNG

CANTY manufactures analyzers designed for the inline measurement of the concentrations and particle size and shape distributions of water and total suspended solids (tss) in LNG lines. Changes to temperature and pressure result in changes to the amount of water that can dissolve in this fluid. As such, making the measurement reliably and inline is critical to ensuring that free water does not damage equipment in your process. Other technologies require samples to be brought to a lab, can be influenced by different kinds of contaminants, and don’t reflect the same information that they would otherwise measure under the actual process conditions.

MORE INFO

POPCORN POLYMER

CANTY manufactures analyzers designed for the automated early detection of the formation of popcorn polymer. This includes measurements of the size and concentration of the polymer material as it first begins forming.

MORE INFO

PRODUCED WATER

Vision technology, when applied correctly, can provide an insight to a process that cannot be gained otherwise. It’s used to monitor and analyze a wide range of multiphase mixtures such as oil and solids in produced water, solids and water in fuels and lube oils, percent solids in separation and filter break applications.

MORE INFO

REFINING

CANTY specializes in many REFINERY applications. Some applications include oil in water / water in oil, hydrogen reformer cameras, and desalter monitors.

MORE INFO

PROPPANT SAND- SOLIDSIZER

The CANTY SolidSizer™ is a vision-based sensor used with the CANTY Vector System image processor for dry sand size measurement in a laboratory environment. The CantyVision™ Software accurately measures multiple aspects of the sand from area / perimeter / minor and major axis / etc. In comparison to a sieve which measures only minor axis the CantyVision™ software can correlate directly to a sieve so the customer does not have to change any QC documents. The SolidSizer™ can correlate within 2% of a sieve. A typical sieve analysis takes anywhere from 20-30 minutes including cleaning and setup for a 70-100 gram sample. On the SolidSizer™ that same sample takes less than 2 minutes. Also multiple screen distributions can be setup to accommodate multiple customers or areas in the process, hence eliminating the need for multiple runs on the same sand for different size distributions. After correlating to current methods of minor axis, customers find benefit in comparing minor axis to major axis and making sure the sand is round instead of needle shaped. Reduce lab time and make sure production samples are not skipped over due to lack of sample time available!

MORE INFO

HYDROGEN REFORMER – ULTRATEMP

The CANTY Ultratemp™ is a vision-based camera system used with the CANTY Vector System image processor to monitor temperature of the tubes inside a hydrogen reformer. The CantyVision™ Software accurately measures temperature as well as bend in the tube for complete control. In comparison to thermocouples which are costly, not reliable, and monitor only one tube, a camera system can monitor multiple tubes at the same time. The CantyVision™ software can output a signal to alarm if the tube has increased in temperature over a certain time to an operator screen, PLC, or DCS for closed loop control. The steam can then be introduced to clean the tube and avoid plugging and then switch back to the natural gas. The pyrometer is not effective for controlling the temperature in the reformer due to the time intervals in between analysis is taken. Also, not everyone measures at the same point and this could lead to a change in temperature when a change never occurred. To calibrate the system the pyrometer can be used initially. If the temperature in the tubes increase over 10°C over 10 min, a plug has a chance to take place. With the Ultratemp™ this event can be avoided completely.

MORE INFO

OIL IN WATER – INFLOW

The CANTY Inflow™ with CantyVision™ Software provides real-time, vision-based measurement of oil in water, accurately distinguishing oil, solids, and gas for reliable data. Unlike fluorescence monitors, it enables visual verification, droplet size analysis, and calibration to existing lab methods, helping optimize separator performance and chemical treatment. In-line monitoring and optional video recording ensure continuous analysis without missed production samples.

MORE INFO