Drilling- Oil & Gas

Showing all 9 results

Particle Size and Shape Analysis (PSSA)

Particle sizing is a critical measurement for products or processes in almost any industry. As the importance of accurate and repeatable particle size measurements has grown, so too has the need to understand and measure particle shape. CANTY manufactures vision-based particle analyzers that are used globally. As the leader in particle size analysis for both lab and online systems, CANTY has a variety of products to measure PSSA in virtually any application.

MORE INFO
Asphaltenes

Features:

• PPM/PPB & particle size distribution

• Water droplet / solids / gas detection

• Image based – real time analysis

MORE INFO
SHORT LOOP SAMPLER – (OIL IN WATER / WATER IN OIL) ANALYZER

The SHORT LOOP SAMPLER™ Oil In Water Analyzer / Water In Oil Analyzer combining sampling point and the INFLOW™ Process Particle Analyzer, provides real time concentration and particle size analysis. The SHORT LOOP SAMPLER™ allows operators and skid manufacturers to test multiple point in their line using only one analyzer and verify the results by using the sample point to verify reading in the lab. Models measure 0.7 micron – 20,000 micron particles under process conditions. By continuously measuring the product OIL, WATER, SAND, and GAS the OiW / WiO concentration and size is output 30 frames a second. This allows the user to see the impact of any change to the refining or drilling system. By using a vision based system CANTY can easily detect all phases and separate them to give PPM/PPB distribution as well as SIZE distribution of all particulates. The system is designed to continuously sample from the center of the process stream and input the entire sample back into the stream so there is no loss of product when analyzing for concentration or particle size.

Min Fluid Velocity: 3 ft/s (If lower consult factory)

Max Fluid Velocity: 15 ft/s

MORE INFO
QUICKSAFE PIG LAUNCH

Features:

• Conforms to ASME Section B 31.1, B31.3 and PED
• Pressure ratings from full vacuum to 10,000 psi, 300F
• No bolting or Torqueing
• Zero Leak Closure
• Dual Seal
• Welded, ANSI or DIN mounting
• Duplex Stainless, Super Duplex, and various Alloys
• Sizes 1” – 20” available
• Optional NACE and corrosion liners

MORE INFO
OIL IN WATER – SKID MOUNTED INFLOW
Features:

Drop in place skid mount design

Cleaning pump & monitor included

PPM/PPB & Particle Size Distribution
MORE INFO
FRAC SAND ANALYSIS – SOLIDSIZER

The CANTY SolidSizer™ is a vision-based sensor used with the CANTY Vector System image processor for dry sand size measurement in a laboratory environment. The CantyVision™ Software accurately measures multiple aspects of the sand from area / perimeter / minor and major axis / etc. In comparison to a sieve which measures only minor axis the CantyVision™ software can correlate directly to a sieve so the customer does not have to change any QC documents. The SolidSizer™ can correlate within 2% of a sieve. A typical sieve analysis takes anywhere from 20-30 minutes including cleaning and setup for a 70-100 gram sample. On the SolidSizer™ that same sample takes less than 2 minutes. Also multiple screen distributions can be setup to accommodate multiple customers or areas in the process, hence eliminating the need for multiple runs on the same sand for different size distributions. After correlating to current methods of minor axis, customers find benefit in comparing minor axis to major axis and making sure the sand is round instead of needle shaped. Reduce lab time and make sure production samples are not skipped over due to lack of sample time available!

MORE INFO
OIL IN WATER – INFLOW
Features:

Inline Analysis – no sample stream needed

No maintenance for about 5 years

PPM/PPB & Particle Size Distribution
MORE INFO
PORTABLE INFLOW OIL IN WATER/WATER IN OIL ANALYZER

The Portable InFlow for OIW/WIO analysis is a rugged analyzer meant for the extreme environments of the petroleum exploration industry. It is a dual analyzer handling the detection of oil in water, or water in oil, depending on the application. It can be quickly installed to take process fluids off line through sampling valves and provide analysis results. The system is easily flushed clean.

MORE INFO
INTERFACE CONTROL

Monitor phase split in batch mode on organic droplets for increased product recovery. As the droplets appear the system warns of organic phase and the upcoming emulsion. The amount of early droplets and their retraction time will indicate the completeness of the separation. Once the split is identified and stopped, the operator has a visual verification from the video monitor. The color can then be analyzed to ensure there is no inversion.

MORE INFO

TOP