-
VECTOR CONTROL MODULE (VCM)
Vector Control Modules (VCMs) serve as image processors for any of CANTY’s applications requiring analysis. These units are built as a turnkey solution to ensure the most convenient and simple startup for a camera system. VCM’s can power camera systems using power over Ethernet (POE) and come pre-loaded with application specific software to best serve your needs. With three different families of models, CANTY provides a variety of VCMs to fit the needs of your installation. See our product brochure for additional information!
-
SHORT LOOP SAMPLER – (OIL IN WATER / WATER IN OIL) ANALYZER
The SHORT LOOP SAMPLER™ combines a sampling point with the INFLOW™ Particle Analyzer to deliver real-time concentration and particle size analysis of oil, water, sand, and gas. It enables operators to test multiple points with one analyzer, verify results in the lab, and continuously measure particles from 0.7 to 20,000 microns at 30 frames per second. Designed to sample from the process stream without product loss, it provides accurate PPM/PPB and size distribution for refining and drilling optimization.
Min Fluid Velocity: 3 ft/s (If lower consult factory)
Max Fluid Velocity: 15 ft/s
BRINE COMPLETION- TSS
-
Drilling Mud Particle Size – Inline
Features:
• Inline Particle size down to 1µm
• Analysis of oil or water based mud
• Detect oil / water / solids / gas
-
Drilling Mud Particle Size – Lab
Features:
• Lab Particle size down to 1µm
• Analysis of oil or water based mud
• Detect oil / water / solids / gas
-
Shaker Screen – Volume Flow & Fluid Front
Features:
• Volume Flow Analysis
• Fluid Front Detection
• Real-Time Viewing
-
PROPPANT SAND- SOLIDSIZER
The CANTY SolidSizer™ is a vision-based sensor used with the CANTY Vector System image processor for dry sand size measurement in a laboratory environment. The CantyVision™ Software accurately measures multiple aspects of the sand from area / perimeter / minor and major axis / etc. In comparison to a sieve which measures only minor axis the CantyVision™ software can correlate directly to a sieve so the customer does not have to change any QC documents. The SolidSizer™ can correlate within 2% of a sieve. A typical sieve analysis takes anywhere from 20-30 minutes including cleaning and setup for a 70-100 gram sample. On the SolidSizer™ that same sample takes less than 2 minutes. Also multiple screen distributions can be setup to accommodate multiple customers or areas in the process, hence eliminating the need for multiple runs on the same sand for different size distributions. After correlating to current methods of minor axis, customers find benefit in comparing minor axis to major axis and making sure the sand is round instead of needle shaped. Reduce lab time and make sure production samples are not skipped over due to lack of sample time available!
-
MUD FLOW ANALYSIS
Features:
- Replace Mud Flappers / Paddles
- Visual Verification
- No Maintenance
DRILLING
-
OIL IN WATER – SKID MOUNTED INFLOW
The CANTY Inflow™ with CantyVision™ Software provides real-time, vision-based measurement of oil in water, accurately distinguishing oil, solids, and gas for reliable data. Unlike fluorescence monitors, it enables visual verification, droplet size analysis, and calibration to existing lab methods, helping optimize separator performance and chemical treatment. In-line monitoring and optional video recording ensure continuous analysis without missed production samples.
-
OIL IN WATER – INFLOW
The CANTY Inflow™ with CantyVision™ Software provides real-time, vision-based measurement of oil in water, accurately distinguishing oil, solids, and gas for reliable data. Unlike fluorescence monitors, it enables visual verification, droplet size analysis, and calibration to existing lab methods, helping optimize separator performance and chemical treatment. In-line monitoring and optional video recording ensure continuous analysis without missed production samples.
-
PORTABLE INFLOW OIL IN WATER/WATER IN OIL ANALYZER
The Portable InFlow for OIW/WIO analysis is a rugged analyzer meant for the extreme environments of the petroleum exploration industry. It is a dual analyzer handling the detection of oil in water, or water in oil, depending on the application. It can be quickly installed to take process fluids off line through sampling valves and provide analysis results. The system is easily flushed clean.
-
SHORT LOOP SAMPLER – (OIL IN WATER / WATER IN OIL) ANALYZER
The SHORT LOOP SAMPLER™ combines a sampling point with the INFLOW™ Particle Analyzer to deliver real-time concentration and particle size analysis of oil, water, sand, and gas. It enables operators to test multiple points with one analyzer, verify results in the lab, and continuously measure particles from 0.7 to 20,000 microns at 30 frames per second. Designed to sample from the process stream without product loss, it provides accurate PPM/PPB and size distribution for refining and drilling optimization.
Min Fluid Velocity: 3 ft/s (If lower consult factory)
Max Fluid Velocity: 15 ft/s
OIL IN WATER
-
OIL IN WATER / WATER IN OIL – TRANSPORTABLE INFLOW (ATEX IECEx)
The Transportable INFLOW™ is designed for multi point site surveys, and testing or trouble shooting of any oilfield separation systems. It combines the latest Gigabit Ethernet camera and microscopic optics technology, with CANTY’s trademark fused glass, LED lighting systems, and CANTYVISION Intelligent Analysis™ software, to provide real time analysis (concentration & size) of Oil and Total Suspended Solids in Water.
-
PRODUCED WATER
Vision technology, when applied correctly, can provide an insight to a process that cannot be gained otherwise. It’s used to monitor and analyze a wide range of multiphase mixtures such as oil and solids in produced water, solids and water in fuels and lube oils, percent solids in separation and filter break applications.
-
OIL IN WATER – INFLOW
The CANTY Inflow™ with CantyVision™ Software provides real-time, vision-based measurement of oil in water, accurately distinguishing oil, solids, and gas for reliable data. Unlike fluorescence monitors, it enables visual verification, droplet size analysis, and calibration to existing lab methods, helping optimize separator performance and chemical treatment. In-line monitoring and optional video recording ensure continuous analysis without missed production samples.
-
INFLOW CART – EXPLOSION PROOF
The EXP version operates similar to the Weather Proof version, with the added benefit of being Explosion Proof rated. The EXP enclosures do add some size and weight to the system, so it is mounted on a larger wheeled cart for increased stability. Configuration and viewing of the systems high speed image processor within the main enclosure, is performed via the units wireless capability using an EXP rated tablet.
-
INFLOW CART – WEATHERPROOF
The compact cart design features a powerful image processor with integral touch screen display, which sits below the automated cleaning system. The INFLOW™ can be mounted to the back of the cart itself, or sit adjacent to the cart depending on the installation location. Once started up, this system runs as an operator free system, with the added feature of mobility around the oilfield facility.
-
OIL IN WATER – SKID MOUNTED INFLOW
The CANTY Inflow™ with CantyVision™ Software provides real-time, vision-based measurement of oil in water, accurately distinguishing oil, solids, and gas for reliable data. Unlike fluorescence monitors, it enables visual verification, droplet size analysis, and calibration to existing lab methods, helping optimize separator performance and chemical treatment. In-line monitoring and optional video recording ensure continuous analysis without missed production samples.
-
PROCESS CAMERA / LIGHT
View and illuminate inside a pressure or process vessel through a single connection. Integrally mounted camera and lighting system (optional) in a connection as small as a 2” NPT.
-
SHORT LOOP SAMPLER – (OIL IN WATER / WATER IN OIL) ANALYZER
The SHORT LOOP SAMPLER™ combines a sampling point with the INFLOW™ Particle Analyzer to deliver real-time concentration and particle size analysis of oil, water, sand, and gas. It enables operators to test multiple points with one analyzer, verify results in the lab, and continuously measure particles from 0.7 to 20,000 microns at 30 frames per second. Designed to sample from the process stream without product loss, it provides accurate PPM/PPB and size distribution for refining and drilling optimization.
Min Fluid Velocity: 3 ft/s (If lower consult factory)
Max Fluid Velocity: 15 ft/s
-
FROTH CONTROL SYSTEMS
An Ethernet camera is used to provide the measurement image to a customer supplied PC. The image from each camera is dynamically analyzed for bubble size, froth velocity and stability. CantyVision™ software is included with each camera. 4-20mA or OPC output to a PLC or DCS for complete automated control.
-
API SEPARATOR CONTROL
API separators are critical devices designed to remove oil and suspended solids from the water stream before it is processed further downstream, primarily in petroleum refineries and petrochemical plants. Separator outlets require monitoring to ensure sufficient separation is occurring. CANTY’s field‑deployable systems provide real‑time monitoring of the various separator points, along with visual verification for operators, eliminating the need to enter the field.
-
DIRECT MOUNT INTERFACE SYSTEM
CANTY’s interface control camera systems provide a powerful, cost-effective solution for measuring and reporting the positions of liquid–liquid and liquid–gas interfaces. With multiple types of systems, these camera systems can be used to retrofit onto existing equipment allowing for this technology to be easily integrated across different industries. The Direct Mount Interface System can be mounted directly on to an existing sight glass.
-
GAUGE LIGHT INTERFACE SYSTEM
CANTY’s interface control camera systems provide a powerful, cost-effective solution for measuring and reporting the positions of liquid–liquid and liquid–gas interfaces. The Gage Light Interface uses our advanced lighting and non-contact vision technology to continuously capture high quality video images of the interface sections through the vessel’s gauge glass. Each image is analyzed to determine the exact position of the interface, and this data is transmitted to a control system, enabling automated responses to changes in interface location.
-
INTERFACE SYSTEM WITH SHROUD
CANTY’s interface control camera systems provide a powerful, cost-effective solution for measuring and reporting the positions of liquid–liquid and liquid–gas interfaces. With multiple types of systems, these camera systems can be used to retrofit onto existing equipment allowing for this technology to be easily integrated across different industries. Due to the dependence of image analysis on controlled lighting, CANTY provides shrouds for systems where external lighting is not otherwise blocked out. These shrouds are made to allow the Interface Camera systems to attach to almost any existing equipment while providing a convenient way to mount and position the camera and light source for the best view of the process.
PRODUCED WATER
-
PROPPANT SAND- SOLIDSIZER
The CANTY SolidSizer™ is a vision-based sensor used with the CANTY Vector System image processor for dry sand size measurement in a laboratory environment. The CantyVision™ Software accurately measures multiple aspects of the sand from area / perimeter / minor and major axis / etc. In comparison to a sieve which measures only minor axis the CantyVision™ software can correlate directly to a sieve so the customer does not have to change any QC documents. The SolidSizer™ can correlate within 2% of a sieve. A typical sieve analysis takes anywhere from 20-30 minutes including cleaning and setup for a 70-100 gram sample. On the SolidSizer™ that same sample takes less than 2 minutes. Also multiple screen distributions can be setup to accommodate multiple customers or areas in the process, hence eliminating the need for multiple runs on the same sand for different size distributions. After correlating to current methods of minor axis, customers find benefit in comparing minor axis to major axis and making sure the sand is round instead of needle shaped. Reduce lab time and make sure production samples are not skipped over due to lack of sample time available!
PROPPANT SAND
-
SHORT LOOP SAMPLER – (OIL IN WATER / WATER IN OIL) ANALYZER
The SHORT LOOP SAMPLER™ combines a sampling point with the INFLOW™ Particle Analyzer to deliver real-time concentration and particle size analysis of oil, water, sand, and gas. It enables operators to test multiple points with one analyzer, verify results in the lab, and continuously measure particles from 0.7 to 20,000 microns at 30 frames per second. Designed to sample from the process stream without product loss, it provides accurate PPM/PPB and size distribution for refining and drilling optimization.
Min Fluid Velocity: 3 ft/s (If lower consult factory)
Max Fluid Velocity: 15 ft/s
-
WATER IN OIL – INFLOW
Features:
- Inline Analysis – no sample stream needed
- No maintenance for about 5 years
- PPM/PPB & Particle Size Distribution
-
PORTABLE INFLOW OIL IN WATER/WATER IN OIL ANALYZER
The Portable InFlow for OIW/WIO analysis is a rugged analyzer meant for the extreme environments of the petroleum exploration industry. It is a dual analyzer handling the detection of oil in water, or water in oil, depending on the application. It can be quickly installed to take process fluids off line through sampling valves and provide analysis results. The system is easily flushed clean.