PARTICLE SIZING

Showing 19–27 of 37 results

INFLOW™ PERCENT SOLIDS MEASUREMENT SYSTEM

Percent Solids measurement is typically a ratio of the area of solid particles vs the background. As solid percentages increase this can also be done by comparing the ratio of light through an empty cell vs light through a cell with solid content. The analysis is frame by frame at a rate in excess of 30 frames per second, so data can be supplied in very short time intervals (seconds) and produce a steady trend line of percent solids readings vs time.

MORE INFO
SOLIDSIZER™ WITH COLOR ANALYSIS

10 um – 2,400 um Particle size analysis range. Finished sugar product is subjected to a series of quality control tests in order to determine if the sugar crystals are the correct size and shape, and also that the concentration of black specks / burned sugar crystals is within specification. CANTY’S range of image based particle analysis systems provide true size and shape characterization, with each particle measured under 13 size and shape parameters. CANTY’S imaging systems also offer the option of Black Speck detection within the sugar sample. The systems can be run at line through the use of a sweep sampler, or offline as laboratory instruments. This system provides direct correlation to traditional sieve analysis, but does so in a much shorter analysis time, with much less operator input required.

MORE INFO
3D ROCKSIZER PARTICLE ANALYSIS SYSTEM

500 um – 6,000 um Particle size analysis range. This system is designed for lab & on-line use to determine particle size, shape and distribution, thereby eliminating the need for sieve analysis.

MORE INFO
INDUSTRIAL SOLIDSIZER™ PARTICLE ANALYSIS SYSTEM

50 um – 2,400 um Particle size analysis range. This system is designed for on-line use to determine particle size, shape and distribution, thereby eliminating the need for sieve analysis.

Related ASTM Standards:
• D8200 – Standard Practice for Creating a Correlation to Compare Particle Size Distribution Results of Proppants by Dynamic Imaging Analysis and Sieves. (D18.26)
• D8392 – Standard Practice for Calibration and Verification of Direct Imaging Analyzers Used for Particle Size and Shape Analysis of Catalytic Materials (D32.02)
• E2589 – Terminology Relating to Non-Sieving Methods of Powder Characterization. (E29.02)

Related ISO Standards:
• 9276-6 Representation of results of particle size analysis – Part 6: Descriptive and quantitative representation of particle shape and morphology.

Canty participates in the referenced ASTM subcommittees (D18.26, D32.02 and E29.02) in order to develop useful standards for imaging analyzers. Although the referenced standards are often particular to a type of particle, they can be generalized for use with many types of particles.
ISO9276-6 is widely used to describe shape parameters and provide corresponding formulae for calculation of values.

MORE INFO
LAB – SOLIDSIZER

The CANTY SolidSizer™ is a vision-based sensor used with the CANTY Vector System image processor for dry particle size measurement in a laboratory environment. The CantyVision™ Software accurately measures multiple aspects of the particles from area / perimeter / minor and major axis / etc. In comparison to a sieve which measures only minor axis the CantyVision™ software can correlate directly to a sieve so the customer does not have to change any QC documents. The SolidSizer™ can correlate within 2% of a sieve. A typical sieve analysis takes anywhere from 20-30 minutes including cleaning and setup for a 70-100 gram sample. On the SolidSizer™ that same sample takes less than 2 minutes. Also multiple screen distributions can be setup to accommodate multiple customers or areas in the process, hence eliminating the need for multiple runs on the same sand for different size distributions. After correlating to current methods of minor axis, customers find benefit in comparing minor axis to major axis and comparing shape factors. Reduce lab time and make sure production samples are not skipped over due to lack of sample time available!

MORE INFO
SOLIDSIZER™ TS SOLID PARTICLE ANALYSIS SYSTEM

10 um – 2,400 um Particle size analysis range. This system is designed for lab use to determine color speck detection, particle size, shape and distribution for flat or needle shape particles.

Relevant ASTM standards:
D8200 Creating a Correlation to Compare Particle Size Distribution Results of Proppants by Dynamic Imaging Analyzers and Sieves.

D8392 Calibration and Verification of Direct Imaging Analyzers Used for Particle Size and Shape Analysis of Catalytic Materials.

MORE INFO
EXPANDED POLYSTYRENE SIZING

A vessel mount system can be used for real time image capture during the production of polymer beads. The captured images are analysed by CantyVision™ software, to provide a complete bead size distribution through the complete process, allowing for greater control over final product size. Applications include pentane injection and end bead size. Also see Solid Particle Sizing for dry bead sizing.

MORE INFO
INFLOW™ PARTICLE SIZING SYSTEM

.7 um – 4800 um Particle size analysis range for inline real time information. This system is designed for inline use with varying pressures, temperatures, and pipe diameters.

MORE INFO
CRYSTALSCOPE PAT PARTICLE SIZING SYSTEM

.7 um – 680 um Particle size analysis range in a reactor for monitoring crystal size in real time from nucleation to full growth. 2D results with no need for multiple probes

MORE INFO

1
2
3
4
5

TOP